The Short Answer: Zinc strips help a clean roof stay clean longer, but they do not remove streaks or moss that are already there. Rain carries zinc down the slope from the strip, and that run-off makes it hard for new algae and moss to take hold. On an Essex roof that is already dark, the growth has to be soft washed off first, and even then the strips only protect the shingles their run-off actually reaches.
In This Guide
Will zinc strips clean a roof that is already streaked?
No. This Old House puts it plainly: zinc strips prevent new growth, but moss, lichen or algae already on the roof still has to be removed.
Those dark streaks are living colonies. The Asphalt Roofing Manufacturers Association names Gloeocapsa magma as probably the most common of the algae behind roof discoloration, and says the stains usually look brown to black and are often mistaken for soot, dirt or tree droppings. A strip of metal at the ridge does nothing to a colony that is already feeding on the shingles below.
Moss is the same story, only thicker. A mat that has rooted between tabs holds water against the roof and lifts the shingle edges as it grows. Waiting for a strip to wear it away just gives it more seasons to spread.
How do zinc strips slow algae and moss from returning?
They work through rain. When it rains, tiny amounts of zinc dissolve off the strip, and as that water flows down the roof the zinc ions keep moss and algae from forming on the surface, according to This Old House.
That makes them a slow, passive treatment. They need regular rain to do anything, and they only touch the shingles the water crosses on its way to the gutter. On a clean roof, that steady wash is often enough to keep spores from settling into a new colony.
The strip is fitted near the ridge, slid under the shingle course with about an inch left showing. Placement high on the roof is what gives the run-off the longest possible path down the slope.
Which parts of a roof do zinc strips miss?
Anything their run-off does not reach. Water runs straight down the slope from the strip, so sections below a dormer, beside a valley or on a lower roof get little or no zinc at all.
Long slopes are a weak spot too. By the time rain from the ridge reaches the eave, it has spread out and carried away much of what it picked up, while the lower courses are often the shadiest and wettest part of the roof. That is why the bottom few rows on a north slope can stay green under a ridge strip that looks like it is working fine.
Take an Essex cape with a wide shed dormer across the back. A ridge strip protects the main slope above the dormer, while the dormer roof and the shingles beside it sit outside the run-off entirely, so they need their own strip or a cleaning schedule of their own.
- Below dormers. The dormer roof blocks the flow from the main ridge.
- Valleys. Water from both slopes funnels in, and much of it never crossed a strip.
- Lower roofs. Porches and garage roofs below the main house need their own strip or get none.
- Behind chimneys and skylights. The run-off splits around them and leaves a dry shadow.
- Shaded eaves. The wettest shingles sit farthest from the strip.
Thinking about zinc strips for a streaked roof? ASAP soft washes shingles with no pressure wand and treats moss instead of scraping it. Call (802) 448-0880 or get a written roof cleaning quote.
Why pair zinc strips with a soft wash?
Because each one does the half of the job the other cannot. A soft wash clears the growth that is already there, and the strips slow the next round from taking hold on the shingles they cover.
The order matters. Strips fitted over a dirty roof start their life trying to hold back colonies that are already established, and the streaks stay visible for years. Washed first, the roof starts from bare shingle and the run-off only has to stop new spores. Think of the wash as the reset and the strip as the upkeep.
How the roof gets clean matters as much. The Asphalt Roofing Manufacturers Association warns against using a power washer or any brush or broom on roof algae, and notes that scrubbing can loosen and remove granules. ASAP uses no pressure wand on shingles, treats moss rather than scraping it, and rinses the gutters and siding below, which the earlier piece on keeping shingles safe during a roof wash explains.
Do algae-resistant shingles make strips unnecessary?
Not always, and they are a roofing choice, not a cleaning one. ARMA says several types of algae-resistant shingles are now available, designed to inhibit algae growth for extended periods.
Most Vermont roofs were put on long before anyone asked about algae resistance. ARMA adds that algae growth turns up in every region of the U.S., especially where conditions are warm and humid, so a damp, shaded roof in the Champlain Valley is fair game in summer.
Metal and cedar roofs are a separate case. Each roofing material takes a different cleaning solution and approach, so the crew sets the method for the roof in front of it rather than for shingles in general.
How is a streaked roof handled in Essex?
It starts with a look at the roof from the ground and the ladder, then a written quote. In Essex the job is the same whether the house sits in Essex Center, Butlers Corners or Pages Corner, the three villages that make up the town.
On paper, the quote spells out how big the roof is, how heavy the growth looks and whether a rinse of the gutters and walls underneath is included. ASAP handles soft wash roof cleaning for streaked shingles in town, and that price comes in writing, free and with no obligation.
If strips are planned for an Essex roof, the wash goes first so they start on clean shingle. Everything else the crew does nearby is gathered under ASAP’s work in Essex.
Frequently Asked Questions
Related services: roof cleaning in Williston and the towns ASAP serves.





